Tools required:

  • 3 mm hex key
  • Small Phillips head screwdriver


Replacement parts required:

  • 000-8082 - Lower PCB



Unplug bike - Make sure the bike is unplugged at the lower stabilizer, not just from the wall.



Remove rear flywheel cap - WARNING: StagesBike MUST be unplugged before moving to this step!


Use a 3 mm hex key to remove the 2 screws that hold the rear flywheel cap in place. Slide the cap backward and set it aside.



Unplug connectors to lower PCB
Next, you will remove all 4 connectors from the exposed PCB



Connector 1: Pull back on the tab to release the clip, then pull down and away from the PCB.



Connector 2: Pull down gently on the connector or all 6 wires at the same time. There is no clip for this connector. If the connector is difficult to remove, a fingernail or small flat head screwdriver can be used to assist removal.




Connector 3: Pull away from the PCB on the 3 wires coming out of the connector. There is no clip for this connector.



Connector 4: Reach around the lower left leg and push on the tab to release the clip, then push the connector away from the PCB.



With all four connectors unplugged, we will now remove PCB from flywheel. We recommend finding a mat or large smooth and dark colored object and placing it beneath the flywheel at this time to catch the small, easy-to-lose screws that are removed in this step. A yoga mat, high thread count blanket or sheet work great.



Using a Phillips screwdriver, remove screws 1-4 in the picture above, then set aside for later.



Use your hand to gently pull the PCB off the flywheel, if it has not already fallen off while unscrewing it.


The replacement PCB comes with an auxiliary PCB connected to it; this is not necessary for this repair. Remove this wire by pulling it away from the PCB, like in previous steps, before installing this replacement PCB on the bike.



Use a Phillips screwdriver and the screws from the previous steps to install the new PCB in the same orientation as before pictured below. We suggest using your finger as a guide to hold the small screw while moving it into place. 




WARNING: Do not over torque screws! These screws only need to be tightened until they touch the PCB, and the PCB is secure against the plastic bosses that touch the back of the PCB. Any further tightening may damage the plastic! These screws are designed to be tight without torque against the PCB.


Check that the PCB is secure by lightly pulling on the green surface of the PCB and making sure there is no play between the screw and plastic bosses.


Replace connectors


WARNING: Each connector requires only a small amount of force to re-install, similar to the force required to squeeze toothpaste out of the tube. If you feel like you are pressing hard on a connector, STOP, re-examine the orientation of the connector and the receiver. It is likely they are backwards!


Small 3-wire connector


Start with the small 3 wire connector. Be sure the wire comes out of the flywheel and beneath the PCB; this connector will only insert one way. Check that the tabs on the short sides of the connector line up with the openings of the receiver. You will also notice that the wire ports are offset.



Press this connector into the receiver until you feel a small click.



6 wire connector


Route the wire of the 6 wire connector such that it does not go through the loop created by the small 3 wire connector.


This connector has a square box that sticks out on one of the 2 long sides, which fits into the opening in the receiver.



Press this connector in until you feel it seat with a slight snap or until there is no visible gap between the receiver and connector.



3 wire connector


Make sure you do not route the wire through the loops created by the previous connections. Align the side of the connector with the clip on it with the top of the receiver on the PCB, then press up until you hear a click.



Large 3 wire connector


This connector is difficult to reach, but using 2 fingers can be installed. Make sure the side of the connector with the clip is aligned with the top of the receiver, then press until you hear a click.



Final wiring check


Check that the wiring on your PCB now looks exactly like this:



Replace rear flywheel cap


Carefully slide the plastic cap back on to the flywheel. The end of the cap behind the left leg must be inserted properly into the front cap in order for the screw holes to properly align. Check that the interface between the two plastic parts is aligned and push towards the front of the bike to get a proper installation.



Proper alignment should be checked before attempting to install the 2 screws, the flywheel contour should match the cover shape in the area indicated below.



Once aligned, use a 3 mm hex key to install the 2 screws that were removed at the start of the instructions. 


WARNING: There is no need to tighten these screws more than enough to hold the cap against the flywheel.

Once all the steps are complete, the rework is done and the bike can be plugged back in and used again.